90 Degree Cast Stainless Steel Elbow-manufacture,factory,supplier from China

Advantages of thin-walled 90-degree elbows: excellent wear resistance and continuous use.90° elbows are suitable for piping systems in petroleum, natural gas, chemical, hydropower, construction and boiler industries.The straight seam elbow with any large diameter and relatively thin wall thickness can be obtained by the casting process. The manufacturing cycle can be shortened and the production cost can be greatly reduced. Because it does not require any special equipment, it is especially suitable for on-site processing of large straight seam elbows.

Sanitary elbow encyclopediaDepending on your requirements, sanitary elbow  can be austenitic or ferritic, and is defined by being seamless and easy to clean, suitable for pharmaceuticals, food and beverage, and drinking water applications.Introduction of sanitary elbow:Material: 304 material and 316L material are two common materials.Product categories: 90 degree long elbow, 90 degree short elbow, 45 degree short elbow, 45 degree long elbow, 180 degree elbow.Connection method: clamp (quick installation) type, butt welding (welding machine) type, thread (slip knot) type.Standard: 3A, DIN,

Laying points of stainless steel elbow in pipeline:1. In order to reduce the heat loss of the stainless steel elbow and prevent thermal deformation, the buried depth of the pipeline should be greater than 1.2 meters. (calculated from the top of the pipe). The burial depth in alpine regions should be appropriately deepened. At the same time, all pipes should be avoided to be laid below the water table.2. For areas where the groundwater level is high or it is difficult to dig deep for other reasons, measures should be taken as far as possible to avoid water insulators before burying the pipes.

Stainless steel is initially by British scientists Henry cabral, doing research on the improvement of weapons found and the stainless steel in which the research has a strong dirt, acid resistance, corrosion resistance, wear resistance, no radioactive environmental products in developed some stainless steel products to pop up to now and slowly instead of the other material products.From material selection to molding, the stainless steel products cast by us have gone through 33 years of process processing. The surface technology adopts stainless steel primary color mirror polishing.

Precautions when installing stainless steel elbows:  1. When installing, the stainless steel elbow can be directly installed on the pipeline according to the connection method, and installed according to the position of use. Under normal circumstances, it can be installed in any position of the pipeline, but it needs to be sealed to prevent leakage and affect the normal operation of the pipeline.2. When the stainless steel elbow ball valve, globe valve and gate valve are used, they are only fully open or fully closed, and should not be used to adjust the flow to avoid sealing.3.

The appearance of the stamping elbow is fixed. Of course, the appearance of the general stamping elbow is based on the different knowledge of the steel pipe. Therefore, in order to ensure the appearance of the stamping elbow, usually after the steel pipe comes in , If it has not been washed by the rain in the yard, then the stamping elbow is pushed by high temperature, and the appearance of the stamping elbow is generally blue. Of course, if it is washed by the rain, we are heating it through high temperature. , the surface color of the heated stamping elbow is red.

Stainless steel can be roughly divided into flat steel and concave-convex steel. The flat steel plate can be divided into three categories: mirror steel plate with surface light reflectivity greater than 90%; The reflectivity is 50%~90% of the light plate; Matte steel plate with reflectivity less than 50%.

The utility of stainless steel flux cored wire is particularly MAG welding, MAG welding has the subsequent characteristics1) Compared with manual welding, welding speed can be advanced 2-4 times, its welding efficiency is as much as 90%(stainless steel electrode only 55%)2) to the current, voltage adaptation range, welding conditions are easy to set, easy to conduct semi-automatic and automated welding. 3) Good slag removal, welding pass surface gloss. In addition, the splash is very small, the arc stability is good, X-ray qualified.

At present, there are few cases of large area stainless steel curtain wall in the field of building exterior wall. Even if large area is adopted, it often does not pursue its high flatness, but only expresses strong texture.For The Chicago Cloud Gate project, each individual steel plate was CNC machined at the factory, cut with a stainless steel plasma torch 3/8 inches thick, and molded using a coil machine created specifically for the project.

Stainless steel X40MnCrN19_DIN 1.3813 X40MnCrN19 stainless steelName: Non-magnetic steelMaterial Number: 1.3813Brand: X40MnCrN19Standard: DIN●X40MnCrN19 features and applications:X40MnCrN19 stainless steel, German non-magnetic steel number.●X40MnCrN19 chemical composition:Carbon C: 0.30 ~ 0.50Si Si: 0.80 or lessManganese Mn: 17.00 ~ 19.00P P: 0.100 or lessS: sulfur 0.030 or lessChromium Cr: 3.00 ~ 5.00Mo Mo: -Ni Ni: -N, N: 0.08 ~ 0.12